6026 Bearing Dimensions

Tolerances and fits for 6026

FULI makes 6026 to P0 as standard, with P6 on request. P0 is the Normal tolerance class of ISO 492; P6 limits are tighter. These are the P0 limits for the 130 × 200 × 33 mm size.

Δdmp and ΔDmp: deviation of the mean bore and mean outside diameter in one radial plane. ΔBs: inner ring width; the outer ring width has the same limits.

Shaft and housing fits (general guidance)

For an inner ring that turns with a solid steel shaft under normal load, bearing makers’ fit tables give 130 m5 for the shaft of 6026. The housing bore is usually H7, or J7 where the outer ring must not creep.

Taking the loosest and the tightest combination of limits, a P0 6026 on a 130 mm m5 shaft has 15 to 58 µm interference. Its outer ring has 0 to 76 µm clearance in an H7 bore and 16 µm interference to 60 µm clearance in a J7 bore.

This is general guidance, not a FULI specification. Heavy or shock loads, a hollow shaft, a thin-walled, split or light-alloy housing, or a large temperature difference between shaft and housing call for other classes, and the drawing of your machine takes priority. A tight shaft fit or a hot housing uses up internal clearance, and that is when C3 is chosen instead of C0.

If the outer ring turns and the shaft stands still, as in an idler pulley or a wheel hub, the fits are reversed: the housing gets the interference fit (for example N7 or P7) and the shaft a sliding one (g6 or h6).

Sources: ISO 492 tables as printed in the NTN catalogue CAT. No. 2203/E (Tables 6.4 and 6.5) and the RKB tolerance catalogue; ISO 286-2 for the seats; SKF and NTN fit tables for the shaft and housing classes.

6026 compared with nearby sizes

6026 measures 130 × 200 × 33 mm: bore d, outside diameter D and width B. Other deep groove ball bearings on this site for the same 130 mm shaft are 6326 (130 × 280 × 58 mm).

6326 is the next heavier choice for a 130 mm shaft, with an outside diameter 80 mm larger (280 mm) and 25 mm more width (58 mm). In FULI's catalog 6326 has a dynamic load rating of 229.00 kN against 106.00 kN and a weight of about 15.30 kg against 3.160 kg for 6026.

6319 has the same 200 mm outside diameter with a 95 mm bore, so it fits the same housing bore on a smaller shaft.

In the 60 (extra light) series the sizes either side of 6026 are 6024 for a 120 mm shaft and 6028 for a 140 mm shaft.

Cr and weight from FULI's catalog; — = not listed on this site.

6026 weight, load ratings and speed

FULI's catalog gives the weight of 6026 as about 3.160 kg, so 100 bearings weigh about 316 kg and 1,000 about 3160 kg before packing. The open, ZZ and 2RS versions share this catalog line.

6026 has a dynamic load rating Cr of 106.00 kN and a static load rating C0r of 101.00 kN. Cr is the load used to work out rating life; C0r is the reference for loads carried while the bearing is stationary or turning slowly. Limiting speeds in the catalog are 3,200 rpm with grease and 3,800 rpm with oil.

Contact seals add friction at the lip, so 6026-2RS usually runs below the speed of the open bearing. Ask us for the limit of the version you order.

Values from FULI's catalog; confirm for your application.

6026 versions: open, ZZ, 2RS and C3

Every version of 6026 has the same 130 × 200 × 33 mm boundary dimensions; only the cover between the rings and the internal clearance change. FULI supplies open, ZZ and 2RS versions, with C0 clearance as standard and C3 on request. Other makers write the same covers as 2Z or ZZ for shields and 2RS1, DDU or LLU for contact seals.

6026 dimensions in inches

The nearest common inch shaft size to the 130 mm bore of 6026 is 5-1/8 in (130.18 mm), 0.18 mm larger than the bore, so 6026 will not go on it. Inch shafts need an inch bearing, not a metric one with a sleeve or shim.

Converted at 1 in = 25.4 mm and rounded to four decimals. The bearing itself is made to the millimetre sizes.

Grease for 6026

FULI fills sealed 6026-2RS and 6026-ZZ bearings to about 30% of the free internal space as standard. The fill is set on an automatic greasing machine after sample sets are weighed before and after greasing. Sealed bearings are not regreased in service. A different fill level, a low-noise grease or a grease for a stated temperature range can be written on the order; for North America a range of −40 to 120 °C is often asked for.

Relubricating 6026 from the side takes about 33.0 g each time by the formula in our grease calculator: 0.005 × D × B = 0.005 × 200 × 33. This applies to the open 6026 in a housing with a grease supply.

How FULI supplies 6026

The standard 6026 from FULI has GCr15 chrome steel rings and balls, P0 precision, C0 radial clearance and vibration grade Z3V3; P6, C3 and other vibration grades are made on request. Radial clearance is set on automatic assembly equipment and sampled during production. Orders with a noise or vibration requirement are tested set by set before packing.

Rings are marked with a brand you are authorised to use, with the FULI brand, or left neutral, as your order states. The box is printed with the model, precision class and brand.

Inquiries that leave out the prefix or suffix letters are the usual cause of a wrong quote, so write the full designation, for example 6026-2RS C3.

Tools and guides for 6026

• Bearing size finder: look up a size from bore, OD and width
• Bearing weight chart
• Bearing grease fill calculator
• Shaft and housing tolerance chart
• Open, ZZ or 2RS seal selector
• Bearing internal clearance: C0, C3 and when to change
• Bearing lubrication basics
• Noise grade and precision class
• Ball bearing vs roller bearing
• All bearing products and model pages